Tag Archives: gear transmission

China Hot selling DIN/ANSI/JIS Standard Sprockets Industrial Gear Teeth Rack Bevel Bicycle Stainless Transmission Drive Part Carbon Steel Plate Idler Wheel Harden Teeth Sprockets

Product Description

SPROCKET  1/2” X 5/16”  08B SERIES SPROCKETS
 

For Chain Acc.to DIN8187 ISO/R 606
Tooth Radius  r3 13.0mm
Radius Width C 1.3mm
Tooth Width b1 7.0mm
Tooth Width B1 7.2mm
Tooth Width B2 21.0mm
Tooth Width B3 34.9mm
08B SERIES ROLLER CHAINS  
Pitch 12.7 mm
Internal Width 7.75 mm
Roller Diameter 8.51 mm

 

 

Z de dp SIMPLEX DUPLEX TRIPLEX
D1 D2 D3
8 37.2  33.18  8 10 10
9 41.0  37.13  8 10 10
10 45.2  41.10  8 10 10
11 48.7  45.07  10 10 12
12 53.0  49.07  10 10 12
13 57.4  53.06  10 10 12
14 61.8  57.07  10 10 12
15 65.5  61.09  10 10 12
16 69.5  65.10  10 12 16
17 73.6  69.11  10 12 16
18 77.8  73.14  10 12 16
19 81.7  77.16  10 12 16
20 85.8  81.19  10 12 16
21 89.7  85.22  12 16 16
22 93.8  89.24  12 16 16
23 98.2  93.27  12 16 16
24 101.8  97.29  12 16 16
25 105.8  101.33  12 16 16
26 110.0  105.36  16 16 16
27 114.0  109.40  16 16 16
28 118.0  113.42  16 16 16
29 122.0  117.46  16 16 16
30 126.1  121.50  16 16 16
31 130.2  125.54  16 16 20
32 134.3  129.56  16 16 20
33 138.4  133.60  16 16 20
34 142.6  137.64  16 16 20
35 146.7  141.68  16 16 20
36 151.0  145.72  16 20 20
37 154.6  149.76  16 20 20
38 158.6  153.80  16 20 20
39 162.7  157.83  16 20 20
40 166.8  161.87  16 20 20
41 171.4  165.91  20 20 25
42 175.4  169.94  20 20 25
43 179.7  173.98  20 20 25
44 183.8  178.02  20 20 25
45 188.0  182.07  20 20 25
46 192.1  186.10  20 20 25
47 196.2  190.14  20 20 25
48 200.3  194.18  20 20 25
49 204.3  198.22  20 20 25
50 208.3  202.26  20 20 25
51 212.1  206.30  20 25 25
52 216.1  210.34  20 25 25
53 220.2  214.37  20 25 25
54 224.1  218.43  20 25 25
55 228.1  222.46  20 25 25
56 232.2  226.50  20 25 25
57 236.4  230.54  20 25 25
58 240.5  234.58  20 25 25
59 244.5  238.62  20 25 25
60 248.6  242.66  20 25 25
62 256.9  250.74  25 25 25
64 265.1  258.82  25 25 25
65 269.0  262.86  25 25 25
66 273.0  266.91  25 25 25
68 281.0  274.99  25 25 25
70 289.0  283.07  25 25 25
72 297.2  291.15  25 25 25
75 309.2  303.28  25 25 25
76 313.2  307.32  25 25 25
78 321.4  315.40  25 25 25
80 329.4  323.49  25 25 25
85 349.0  343.69  25 25 25
90 369.9  363.90  25 25 25
95 390.1  384.11  25 25 25
100 410.3  404.32  25 25 25
110 450.7  444.74  25 25 25
114 466.9  460.91  25 25 25
120 491.2  485.16  25 25 25
125 511.3  505.37  25 25 25

BASIC INFO.

Type:

Simplex, Duplex, Triplex

Sprocket Model:

3/8″,1/2″,5/8″,3/4″,1″,1.25″,1.50″,1.75″,2.00″,2.25″,2.00″,2.25″,2.50″, 3″

Teeth Number:

9-100

Standard:

ANSI , JIS, DIN, ISO

Material:

1571, 1045, SS304 , SS316;  As Per User Request.

Performance Treatment:

Carburizing, High Frequency Treatment, Hardening and Tempering, Nitriding

Surface Treatment:

Black of Oxidation, Zincing, Nickelage.

Characteristic Fire Resistant, Oil Resistant, Heat Resistant, CZPT resistance, Oxidative resistance, Corrosion resistance, etc
Design criterion ISO DIN ANSI & Customer Drawings
Application Industrial transmission equipment
Package Wooden Case / Container and pallet, or made-to-order

Certification:

ISO9001 SGS

Quality Inspection:

Self-check and Final-check

Sample:

ODM&OEM, Trial Order Available and Welcome

Advantage Quality first, Service first, Competitive price, Fast delivery
Delivery Time 10 days for samples. 15 days for official order.

 

INSTALLATION AND USING

The chain spocket, as a drive or deflection for chains, has pockets to hold the chain links with a D-profile cross section with flat side surfaces  parallel to the centre plane of the chain links, and outer surfaces at right angles to the chain link centre plane. The chain links are pressed firmly against the outer surfaces and each of the side surfaces by the angled laying surfaces at the base of the pockets, and also the support surfaces of the wheel body together with the end sides of the webs formed by the leading and trailing walls of the pocket.

NOTICE

When fitting new chainwheels it is very important that a new chain is fitted at the same time, and vice versa. Using an old chain with new sprockets, or a new chain with old sprockets will cause rapid wear.

It is important if you are installing the chainwheels yourself to have the factory service manual specific to your model. Our chainwheels are made to be a direct replacement for your OEM chainwheels and as such, the installation should be performed according to your models service manual.

During use a chain will stretch (i.e. the pins will wear causing extension of the chain). Using a chain which has been stretched more than the above maximum allowance causes the chain to ride up the teeth of the sprocket. This causes damage to the tips of the chainwheels teeth, as the force transmitted by the chain is transmitted entirely through the top of the tooth, rather than the whole tooth. This results in severe wearing of the chainwheel.
 

FOR CHAIN STHangZhouRDS

Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.

ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25

ASME/ANSI B29.1-2011 Roller Chain Standard Sizes
Size Pitch Maximum Roller Diameter Minimum Ultimate Tensile Strength Measuring Load
25 0.250 in (6.35 mm) 0.130 in (3.30 mm) 780 lb (350 kg) 18 lb (8.2 kg)
35 0.375 in (9.53 mm) 0.200 in (5.08 mm) 1,760 lb (800 kg) 18 lb (8.2 kg)
41 0.500 in (12.70 mm) 0.306 in (7.77 mm) 1,500 lb (680 kg) 18 lb (8.2 kg)
40 0.500 in (12.70 mm) 0.312 in (7.92 mm) 3,125 lb (1,417 kg) 31 lb (14 kg)
50 0.625 in (15.88 mm) 0.400 in (10.16 mm) 4,880 lb (2,210 kg) 49 lb (22 kg)
60 0.750 in (19.05 mm) 0.469 in (11.91 mm) 7,030 lb (3,190 kg) 70 lb (32 kg)
80 1.000 in (25.40 mm) 0.625 in (15.88 mm) 12,500 lb (5,700 kg) 125 lb (57 kg)
100 1.250 in (31.75 mm) 0.750 in (19.05 mm) 19,531 lb (8,859 kg) 195 lb (88 kg)
120 1.500 in (38.10 mm) 0.875 in (22.23 mm) 28,125 lb (12,757 kg) 281 lb (127 kg)
140 1.750 in (44.45 mm) 1.000 in (25.40 mm) 38,280 lb (17,360 kg) 383 lb (174 kg)
160 2.000 in (50.80 mm) 1.125 in (28.58 mm) 50,000 lb (23,000 kg) 500 lb (230 kg)
180 2.250 in (57.15 mm) 1.460 in (37.08 mm) 63,280 lb (28,700 kg) 633 lb (287 kg)
200 2.500 in (63.50 mm) 1.562 in (39.67 mm) 78,175 lb (35,460 kg) 781 lb (354 kg)
240 3.000 in (76.20 mm) 1.875 in (47.63 mm) 112,500 lb (51,000 kg) 1,000 lb (450 kg

For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):

Pitch (inches) Pitch expressed
in eighths
ANSI standard
chain number
Width (inches)
14 28 25 18
38 38 35 316
12 48 41 14
12 48 40 516
58 58 50 38
34 68 60 12
1 88 80 58

Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
 A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.

Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.

Roller chains made using ISO standard are sometimes called as isochains.

 

WHY CHOOSE US 
 

1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CZPT Marketing Network
7. Efficient After-Sale Service System

 

The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.

We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CZPT range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.

 

Standard Or Nonstandard: Standard
Application: Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car
Hardness: Hardened Tooth Surface
Samples:
US$ 0/Piece
1 Piece(Min.Order)

|

Order Sample

Customization:
Available

|

Customized Request

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost:

Estimated freight per unit.







about shipping cost and estimated delivery time.
Payment Method:







 

Initial Payment



Full Payment
Currency: US$
Return&refunds: You can apply for a refund up to 30 days after receipt of the products.

drive sprocket

What are the noise and vibration levels associated with drive sprocket systems?

The noise and vibration levels associated with drive sprocket systems can vary depending on several factors, including the type of sprocket, the design of the system, the speed of operation, and the condition of the components. Here are some key points to consider:

  • 1. Roller Chain Sprockets: In systems that use roller chains, the noise and vibration levels are generally higher compared to other types of power transmission systems. The impact of the chain engaging with the sprocket teeth can produce noise and vibration, especially at higher speeds.
  • 2. Tooth Profile and Design: The design and profile of the sprocket teeth can influence the noise level. Sprockets with irregular tooth profiles or poor manufacturing may produce higher noise and vibration levels.
  • 3. Lubrication: Proper lubrication of the sprocket and chain can help reduce noise and vibration by minimizing metal-to-metal contact and reducing friction.
  • 4. Alignment and Tension: Misalignment of the sprockets or improper chain tension can lead to increased noise and vibration due to uneven loading and wear.
  • 5. Wear and Maintenance: Worn-out sprockets or chains can increase noise levels and cause vibrations. Regular inspection and maintenance can help identify and address such issues.
  • 6. Damping and Isolation: In some applications, damping and isolation techniques may be used to reduce the transmission of vibrations to other parts of the machinery.

To minimize noise and vibration levels in drive sprocket systems, it’s essential to choose high-quality sprockets and chains, ensure proper alignment and tension, and perform regular maintenance. Additionally, using noise-absorbing materials and employing vibration isolation techniques can further help in reducing the overall noise and vibration levels in the system.

drive sprocket

What are the best practices for storing spare drive sprockets when not in use?

Proper storage of spare drive sprockets is essential to maintain their performance and longevity. When not in use, follow these best practices for storing spare drive sprockets:

  • Clean the Sprockets: Before storing, make sure the sprockets are clean and free from dirt, debris, or any contaminants. Use a brush or cloth to remove any buildup on the sprocket’s teeth and surfaces.
  • Inspect for Damage: Check the sprockets for any signs of wear, damage, or deformation. If you notice any issues, address them before storage, or consider replacing the sprocket if necessary.
  • Keep in a Dry Environment: Store the sprockets in a dry and controlled environment to prevent rust or corrosion. Moisture can lead to deterioration of the sprockets over time.
  • Avoid Direct Sunlight: Keep the sprockets away from direct sunlight or sources of heat. Prolonged exposure to sunlight can degrade certain materials and affect the sprockets’ performance.
  • Use Original Packaging: If possible, store the sprockets in their original packaging. The original packaging provides protection and prevents them from coming into contact with other objects that may cause damage.
  • Keep Away from Chemicals: Avoid storing the sprockets near any chemicals or substances that could potentially cause damage or reactions with the material of the sprockets.
  • Organize and Label: If you have multiple spare sprockets, organize and label them accordingly for easy identification and retrieval.
  • Elevate from the Ground: Store the sprockets on pallets, shelves, or racks to keep them off the ground and away from potential hazards or moisture.
  • Rotate Stock: If you have a stock of spare sprockets, rotate them periodically to ensure that older sprockets are used first, preventing any sprockets from sitting in storage for too long.

By following these best practices, you can ensure that your spare drive sprockets remain in good condition and are ready for use whenever they are needed.

drive sprocket

How do drive sprockets work in conjunction with chains and other components?

In a mechanical power transmission system, drive sprockets play a vital role in working with chains and other components to transfer rotational motion and power from one shaft to another. The interaction between drive sprockets, chains, and additional components is essential for the efficient functioning of the system.

1. Chain Engagement: Drive sprockets are designed with teeth that correspond to the pitch of the chain they are intended to work with. When power is applied to the drive sprocket, it rotates, causing the teeth to engage with the links of the chain. This engagement creates a positive drive system, where the sprocket and chain move in sync, transmitting motion and power along the chain’s length.

2. Chain Wrap: The chain wraps partially around the circumference of the drive sprocket. The degree of wrap, known as the chain wrap angle, influences the efficiency of power transmission and the sprocket’s ability to maintain a secure grip on the chain. A larger chain wrap angle generally results in better power transmission and reduced likelihood of chain slippage.

3. Chain Tension: To maintain proper chain engagement, tension must be applied to the chain. Drive sprockets are often mounted on an adjustable shaft or a tensioner to ensure the chain remains tight. Proper chain tension prevents excess slack, reduces vibration, and minimizes the risk of the chain disengaging from the sprocket.

4. Interaction with Driven Sprockets: In many systems, the drive sprocket is connected to a driven sprocket through a continuous loop of chain. When the drive sprocket rotates, it pulls the chain along, causing the driven sprocket to rotate as well. This allows the transmission of motion and power from the input shaft (connected to the drive sprocket) to the output shaft (connected to the driven sprocket).

5. Gear Ratio: The combination of the number of teeth on the drive sprocket and the driven sprocket determines the gear ratio of the system. The gear ratio affects the speed and torque output of the mechanical system. By altering the size of the sprockets, the gear ratio can be modified to suit specific operational requirements.

6. Lubrication: Proper lubrication of the chain-sprocket interface is crucial for reducing friction, wear, and noise. Lubricants ensure smooth movement of the chain on the sprocket, thereby enhancing the overall efficiency and lifespan of the system.

Overall, drive sprockets, in conjunction with chains and other components, facilitate the efficient and reliable transfer of power in mechanical systems. Their precise design, engagement with the chain, and interaction with driven sprockets ensure smooth and controlled motion, making them essential components in a wide range of applications.

China Hot selling DIN/ANSI/JIS Standard Sprockets Industrial Gear Teeth Rack Bevel Bicycle Stainless Transmission Drive Part Carbon Steel Plate Idler Wheel Harden Teeth Sprockets  China Hot selling DIN/ANSI/JIS Standard Sprockets Industrial Gear Teeth Rack Bevel Bicycle Stainless Transmission Drive Part Carbon Steel Plate Idler Wheel Harden Teeth Sprockets
editor by CX 2023-10-17

China Standard Chain Conveyor Transmission Parts Stainless Steel Idler Taper Transmission Drive Gear Wheel Roller Chain Sprockets manufacturer

Product Description

SPROCKET  5/8” X 3/8”  10B SERIES SPROCKETS
 

For Chain Acc.to DIN8187 ISO/R 606
Tooth Radius  r3 16.0mm
Radius Width C 1.6mm
Tooth Width b1 9.0mm
Tooth Width B1 9.1mm
Tooth Width B2 25.5mm
Tooth Width B3 42.1mm
10B SERIES ROLLER CHAINS  
Pitch 15.875 mm
Internal Width 9.65 mm
Roller Diameter 10.16 mm

 

 

Z de dp SIMPLEX DUPLEX TRIPLEX
dm D1 A dm D2 A dm D3 A
8 47.0 41.48 25 10 25 25 12 40 25 12 55
9 52.6 46.42 30 10 25 30 12 40 30 12 55
10 57.5 51.37 35 10 25 35 12 40 35 12 55
11 63.0 56.34 37 12 30 39 14 40 39 16 55
12 68.0 61.34 42 12 30 44 14 40 44 16 55
13 73.0 66.32 47 12 30 49 14 40 49 16 55
14 78.0 71.34 52 12 30 54 14 40 54 16 55
15 83.0 76.36 57 12 30 59 14 40 59 16 55
16 88.0 81.37 60 12 30 64 16 45 64 16 60
17 93.0 86.39 60 12 30 69 16 45 69 16 60
18 98.3 91.42 70 14 30 74 16 45 74 16 60
19 103.3 96.45 70 14 30 79 16 45 79 16 60
20 108.4 101.49 75 14 30 84 16 45 84 16 60
21 113.4 106.52 75 16 30 85 16 45 85 20 60
22 118.0 111.55 80 16 30 90 16 45 90 20 60
23 123.5 116.58 80 16 30 95 16 45 95 20 60
24 128.3 121.62 80 16 30 100 16 45 100 20 60
25 134.0 126.66 80 16 30 105 16 45 105 20 60
26 139.0 131.70 85 20 35 110 20 45 110 20 60
27 144.0 136.75 85 20 35 110 20 45 110 20 60
28 148.7 141.78 90 20 35 115 20 45 115 20 60
29 153.8 146.83 90 20 35 115 20 45 115 20 60
30 158.8 151.87 90 20 35 120 20 45 120 20 60
31 163.9 156.92 95 20 35 120 20 45 120 20 60
32 168.9 161.95 95 20 35 120 20 45 120 20 60
33 174.5 167.00 95 20 35 120 20 45 120 20 60
34 179.0 172.05 95 20 35 120 20 45 120 20 60
35 184.1 177.10 95 20 35 120 20 45 120 20 60
36 189.1 182.15 100 20 35 120 20 45 120 25 60
37 194.2 187.20 100 20 35 120 20 45 120 25 60
38 199.2 192.24 100 20 35 120 20 45 120 25 60
39 204.2 197.29 100 20 35 120 20 45 120 25 60
40 209.3 202.34 100 20 35 120 20 45 120 25 60
41 214.8 207.38 *100 20 40 120 20 50 *130 25 60
42 2,199 212.43 *100 20 40 120 20 50 *130 25 60
43 224.9 217.48 *100 20 40 120 20 50 *130 25 60
44 230.0 222.53 *100 20 40 120 20 50 *130 25 60
45 235.0 227.58 *100 20 40 *120 20 50 *130 25 60
46 240.1 232.63 *100 20 40 *120 20 50 *130 25 60
47 245.1 237.68 *100 20 40 *120 20 50 *130 25 60
48 250.2 242.73 *100 20 40 *120 20 50 *130 25 60
49 255.2 247.78 *100 20 40 *120 20 50 *130 25 60
50 260.3 252.82 *100 20 40 *120 20 50 *130 25 60
51 265.3 257.87 *100 20 40 *120 20 50 *130 25 60
52 270.4 262.92 *100 20 40 *120 20 50 *130 25 60
53 275.4 267.97 *100 20 40 *120 20 50 *130 25 60
54 280.5 273.03 *100 20 40 *120 20 50 *130 25 60
55 285.5 278.08 *100 20 40 *120 20 50 *130 25 60
56 290.6 283.13 *100 20 40 *120 20 50 *130 25 60
57 296.0 288.18 *100 20 40 *120 20 50 *130 25 60
58 300.7 293.23 *100 20 43 *120 20 57 *130 25 64
59 305.7 298.28 *100 20 43 *120 20 57 *130 25 64
60 310.8 303.33 *100 20 43 *120 20 57 *130 25 64
62 321.4 313.43 *100 20 43 *120 20 57 *130 25 64
64 331.5 323.53 *100 20 43 *120 20 57 *130 25 67
65 336.5 328.58 *100 20 43 *120 20 57 *130 25 67
66 341.6 333.64 *100 20 43 *120 20 57 *130 25 67
68 351.7 343.74 *100 20 43 *120 20 57 *130 25 67
70 361.8 353.84 *100 20 43 *120 20 57 *130 25 67
72 371.9 363.94 *100 20 43 *120 20 57 *130 25 67
75 387.1 379.10 *100 20 43 *120 20 57 *130 25 67
76 392.1 384.15 *100 20 43 *120 20 57 *130 25 67
78 402.2 394.25 *100 20 43 *120 20 57 *130 25 67
80 412.3 404.36 *100 20 43 *130 20 57 *130 25 67
85 437.6 429.62 *100 20 50 *130 20 58 *130 25 67
90 462.8 454.88 *100 20 50 *130 20 58 *130 25 67
95 488.5 480.14 *100 20 50 *130 20 58 *130 25 67
100 513.4 505.40 *100 20 50 *130 20 58 *130 25 67
110 563.9 555.92 *100 20 50 *130 20 58 *130 25 67
114 584.1 576.13 *100 20 50 *130 20 58 *130 25 67
120 614.4 606.45 *100 20 50 *130 20 58 *130 25 67
125 639.7 631.51 *100 20 50 *130 20 58 *130 25 67

Notice: *welding hub

BASIC INFO.
 

Product name  DIN ISO Standard Sprocket for Roller Chain
Materials Available  1. Stainless Steel: SS304, SS316, etc
2. Alloy Steel: C45, 45Mn, 42CrMo, 20CrMo, etc
3. OEM according to your request
Surface Treatment Heat treatment, Quenching treatment, High frequency normalizing treatment, Polishing, Electrophoresis paint processing, Anodic oxidation treatment, etc
Characteristic Fire Resistant, Oil Resistant, Heat Resistant, CZPT resistance, Oxidative resistance, Corrosion resistance, etc
Design criterion ISO DIN ANSI & Customer Drawings
Size Customer Drawings & ISO standard 
Application Industrial transmission equipment
Package Wooden Case / Container and pallet, or made-to-order
Certificate ISO9001: 2008 
Advantage Quality first, Service first, Competitive price, Fast delivery
Delivery Time 20 days for samples. 45 days for official order.

INSTALLATION AND USING

The chain  spoket, as a drive or deflection for chains, has pockets to hold the chain links with a D-profile cross section with flat side surfaces  parallel to the centre plane of the chain links, and outer surfaces at right angles to the chain link centre plane. The chain links are pressed firmly against the outer surfaces and each of the side surfaces by the angled laying surfaces at the base of the pockets, and also the support surfaces of the wheel body together with the end sides of the webs formed by the leading and trailing walls of the pocket.

NOTICE

When fitting new chainwheels it is very important that a new chain is fitted at the same time, and vice versa. Using an old chain with new sprockets, or a new chain with old sprockets will cause rapid wear.

It is important if you are installing the chainwheels yourself to have the factory service manual specific to your model. Our chainwheels are made to be a direct replacement for your OEM chainwheels and as such, the installation should be performed according to your models service manual.

During use a chain will stretch (i.e. the pins will wear causing extension of the chain). Using a chain which has been stretched more than the above maximum allowance causes the chain to ride up the teeth of the sprocket. This causes damage to the tips of the chainwheels teeth, as the force transmitted by the chain is transmitted entirely through the top of the tooth, rather than the whole tooth. This results in severe wearing of the chainwheel.
 

FOR CHAIN STHangZhouRDS

Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.

ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25

ASME/ANSI B29.1-2011 Roller Chain Standard Sizes
Size Pitch Maximum Roller Diameter Minimum Ultimate Tensile Strength Measuring Load
25 0.250 in (6.35 mm) 0.130 in (3.30 mm) 780 lb (350 kg) 18 lb (8.2 kg)
35 0.375 in (9.53 mm) 0.200 in (5.08 mm) 1,760 lb (800 kg) 18 lb (8.2 kg)
41 0.500 in (12.70 mm) 0.306 in (7.77 mm) 1,500 lb (680 kg) 18 lb (8.2 kg)
40 0.500 in (12.70 mm) 0.312 in (7.92 mm) 3,125 lb (1,417 kg) 31 lb (14 kg)
50 0.625 in (15.88 mm) 0.400 in (10.16 mm) 4,880 lb (2,210 kg) 49 lb (22 kg)
60 0.750 in (19.05 mm) 0.469 in (11.91 mm) 7,030 lb (3,190 kg) 70 lb (32 kg)
80 1.000 in (25.40 mm) 0.625 in (15.88 mm) 12,500 lb (5,700 kg) 125 lb (57 kg)
100 1.250 in (31.75 mm) 0.750 in (19.05 mm) 19,531 lb (8,859 kg) 195 lb (88 kg)
120 1.500 in (38.10 mm) 0.875 in (22.23 mm) 28,125 lb (12,757 kg) 281 lb (127 kg)
140 1.750 in (44.45 mm) 1.000 in (25.40 mm) 38,280 lb (17,360 kg) 383 lb (174 kg)
160 2.000 in (50.80 mm) 1.125 in (28.58 mm) 50,000 lb (23,000 kg) 500 lb (230 kg)
180 2.250 in (57.15 mm) 1.460 in (37.08 mm) 63,280 lb (28,700 kg) 633 lb (287 kg)
200 2.500 in (63.50 mm) 1.562 in (39.67 mm) 78,175 lb (35,460 kg) 781 lb (354 kg)
240 3.000 in (76.20 mm) 1.875 in (47.63 mm) 112,500 lb (51,000 kg) 1,000 lb (450 kg

For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):

Pitch (inches) Pitch expressed
in eighths
ANSI standard
chain number
Width (inches)
14 28 25 18
38 38 35 316
12 48 41 14
12 48 40 516
58 58 50 38
34 68 60 12
1 88 80 58

Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
 A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.

Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.

Roller chains made using ISO standard are sometimes called as isochains.

 

WHY CHOOSE US 

1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CZPT Marketing Network
7. Efficient After-Sale Service System

 

The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.

We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CZPT range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.

 

 

Standard Or Nonstandard: Nonstandard, Standard
Application: Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car, Motor, Electric Cars, Motorcycle, Machinery,
Hardness: Hardened Tooth Surface
Manufacturing Method: Cut Gear, Rolling Gear
Toothed Portion Shape: Spur Gear
Material: Alloy Steel, 1045, Stainless Steel, Q235, Brass,
Samples:
US$ 0/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request

sprocket

Sprocket Basics

When it comes to sprockets, it’s important to understand the basics of design. This includes chain size and number of teeth. The number of teeth will vary depending on the type of chain and application. When determining the number of teeth, the angle between the teeth should be at least 360 degrees.

size

There are many factors to consider when choosing the correct sprocket size. The first thing to do is to determine if the sprocket is a double sprocket or a single sprocket. Also available in a variety of sizes. To determine the exact size, you should measure the distance between the grooves of the sprocket teeth and their opposite tooth slots. The distance between these two points is called the caliper diameter.
The size of the sprockets also varies depending on the type of chain. Large sprockets have arms, while smaller sprockets usually don’t. The arms reduce weight and inertia, making them more economical to operate. Some sprockets also have openings, which make them easier to assemble and disassemble. Some sprockets are also plated for a stronger construction. Some sprockets are manufactured with flame or induction hardened parts.
Sprockets are often used in conveyors, pallet conveyors and other conveying systems. The size of the sprocket should match the size of the chain. A caliper will help you determine if the sprocket has worn teeth. Another way to identify worn sprockets is to measure their diameter.
In addition to size, sprockets should have the correct pitch and center distance. This will help keep the roller chain taut. The chain should be clean and properly lubricated. There should be a small gap between the pin and bushing so that oil can pass through the sprocket and chain. In addition to this, the center-to-center distance between the chain and the sprocket should be at least 1.5 times the diameter of the sprocket.
The chain should have at least 17 teeth, which is common in the industry. Having smaller spacing will reduce mechanical losses and noise. However, larger sprocket sizes are best for applications with higher workloads.

Material

Sprockets are mechanical parts that mesh with the chain to move the chain. It is made of metal or reinforced plastic and usually resembles a gear. It is a gear design for a specific type of chain. Most sprocket and chain systems work the same way, although they vary in material and pitch.
There are three basic types of sprockets: single-strand, double-strand, and triple-strand. The length and number of teeth for each type are specified by various standards. For reference, the ISO-DIN standard is shown. Most sprockets are made of alloy steel and are case hardened and tempered in the tooth area. They also have a hub and a key for mounting.
Metal sprockets can be made of steel or aluminum alloys. While steel is a more durable material, aluminum sprockets are more attractive. Steel is the best material for long rides, while aluminum sprockets are better for casual riding.
In addition to automotive and industrial applications, sprockets are used in oil and gas, textile machinery, instrumentation and mechanical transmission. Many types of sprockets are interchangeable with each other. For added protection, they can also be galvanized to prevent rust. The main methods of galvanizing sprockets are hot-dip galvanizing and electro-galvanizing.
Sprockets are usually made of steel or aluminum. Their design is similar to that of gears, although they are more widely spaced than their counterparts. They can also span longer distances than gears, allowing them to be used for power transmission.
sprocket

Function

A chain drive is a common type of mechanical transmission in which sprockets are used to help reduce the speed of a moving object. Sprockets can have horizontal, vertical or inclined pitch and are usually used in pairs. The teeth of the sprocket mesh with the rollers on the drive chain, reducing the speed. These sprockets are usually made of metal, but can also be made of plastic or composite materials.
The role of the sprocket is to transmit motion from the output shaft of the engine to the rear wheels. For this, the front sprocket needs to rotate at the same speed as the engine output shaft. It can be mounted either on the drive track or on the front of the vehicle. A third sprocket can be connected to the drive track. In addition, the front sprocket is used to pull the drive chain. This will help transfer power from the engine to the rear wheels, allowing the motorcycle to travel forward. The side plates of the chain also help transmit chain tension.
The bushings are subjected to the tension applied to the chain as it passes through the sprockets thousands of times per minute. This puts pressure on the pin inside the bushing. Additionally, the pins must withstand bending and shearing forces transmitted from the plate to the bushing. The pins must also withstand impact and have high tensile strength. If the pin is worn, it will need to be replaced or repaired.
Sprockets power the chain-driven motion system and carry heavy loads. Proper selection of sprockets can prevent damage to your equipment. To do this, you need to select the appropriate sprocket based on the type of assembly and system specification.
sprocket

maintain

Sprocket maintenance is an important part of motorcycle maintenance. Failure to do so will result in frequent chain changes and additional costs. Regular maintenance of your chain will help ensure your chain will last 30,000 miles or more. By comparison, a poorly maintained chain only lasts 10,000 miles.
Checking the sprocket is very easy. First, remove the chain and align it. Next, check for any foreign objects. If you see a damaged sprocket, you need to replace it. If you can’t replace a worn sprocket, you can buy a new chain. However, the new chain will not last as long as the old one.
Check for signs of rust. Rust can form on the chain due to exposure to humidity and heat. When the pins or rollers get rusted, the seals are damaged. If the pins or rollers are rusted, it’s time to replace the chain.
Regular maintenance of the chain is important to prevent kinks and slippage. This can cause excessive wear on the sprockets and chain. If the teeth are worn, the chain will not be able to properly grip the sprocket, resulting in difficult shifting and severe vibration.
If your chain is several years old, it is important to lubricate it every few months to prevent rust. It is also important to clean the chain thoroughly before lubricating to keep it clean and lubricated. Non-petroleum-based cleaners can help remove grit that may have built up. If you use the chain for a long time, you will need to clean it every 300-600 miles.

China Standard Chain Conveyor Transmission Parts Stainless Steel Idler Taper Transmission Drive Gear Wheel Roller Chain Sprockets     manufacturer China Standard Chain Conveyor Transmission Parts Stainless Steel Idler Taper Transmission Drive Gear Wheel Roller Chain Sprockets     manufacturer
editor by CX 2023-06-07

China supplier Standard Rolling Gear Sea/Plywood Case Various Shaoxing Transmission Part Sprockets with Hot selling

Product Description

ZHangZhoug CZPT Machinery Co., Ltd
(DIN/ANSI/JIS Standard or made to drawing)
Product Description:

Detailed Photos:

Company Profile:

ZHangZhoug CZPT Machinery Co., Ltd. Is the vice chairman of chain Transmission Branch of China Machinery General parts Industry Association and a member of China chain Transmission Standardization Technical Committee.

Founded in 1954, mainly engaged in sprocket, gear, timing belt pulley, coupling production and sales, It is a large sprocket manufacturing enterprise in China, and it is also 1 of the largest standard sprocket manufacturers in the world at present. The product structure of the company has been developed from the single pattern of standard sprocket to non-standard transmission parts. Products are mainly sold in North America, South America, Europe, Africa and Japan, South Korea, the Middle East, Russia and Southeast Asia and other countries and regions, sales network all over the world.

The company has passed ISO 9002 quality assurance system certification for the first time in 1999, ISO9001: 2000 quality management system certification in 2003, ISO/TS16949 quality management system certification for the first time in 2009, ISO14001: 2004 environmental management system certification for the first time in 2571, ISO14001: 2015 environmental management system certification for 2017, and ISO9001: 2015 and IATF16949: 2016 quality management system certification for 2018. It lays a CZPT foundation for perfecting the internal management of the enterprise and opening up the external market.

The company adheres to the business philosophy of “Quality is life, technology is physique, delivery is moral, quantity is credit, service is kindred, cost is lifetime”, implementing “innovation-driven, twinning integration” upgrading strategy, promoting chain transmission products to excellence, and making every effort to create “harmonious cenfit, good quality cenfit, hundred years of cenfit”

Standard Or Nonstandard: Standard
Application: Motor, Machinery, Agricultural Machinery, Car
Hardness: Hardened Tooth Surface
Manufacturing Method: Rolling Gear
Toothed Portion Shape: Spur Gear
Material: C45
Customization:
Available

|

Customized Request

sprocket

Problems with sprockets

If you’re having trouble with your HP Sprocket, you’re not alone. This bike component isn’t without issues, but it’s also susceptible to other wear and tear. Check for worn tooth surfaces and hooked tips. When teeth wear out quickly, they can break the chain, so make sure you fix them as soon as possible.
You can solve this issue by installing the latest firmware update for your Sprocket printer. The firmware update is designed to provide a safe and reliable printing experience. When your Sprocket printer doesn’t print the pictures, it is likely because it’s not receiving enough power from the battery. Make sure the battery is at least 25% before you begin.
Insufficient or improper lubrication can cause a variety of problems. Proper lubrication can prevent or remove excessive wear, or protect the chain from the environment. It can also reduce the risk of excessive chain slack. The following are just a few common problems that can cause slack in the chain.
In case of excessive wear, a new sprocket may be necessary. If the sprocket and chain do not match, replace them with a similar size. In addition, a shock absorber can be installed to minimize load. Another alternative is to install a take-up idler, which helps prevent excessive chain elongation.
Improper alignment of the sprocket is another common cause of chain drive problems. If the sprocket is not aligned correctly, it will not be able to move smoothly through the chain during rotation. The teeth of the sprocket will become hooked, preventing the roller from smoothly moving through. This will force the roller chain to cling to the sprocket, and need to be replaced.

Common types of sprockets

Power transmission equipment typically utilizes sprockets and chains. These are used in pairs to provide speed reduction. They are different from gears because the teeth of the sprocket do not mesh with those of the mating gears. They are typically made of plastic, but they can also be made of metal.
There are many common types of sprockets and chains. Some of these types of sprockets have large, narrow, or variable tooth pitch. The size of the sprocket depends on the size and pitch of the chain. If you are using a chain with a large pitch diameter, you should use a sprocket with large teeth. Conversely, a smaller pitch diameter will require a sprocket with small teeth.
Another way to identify the type of sprocket you’re using is to look at the number of strands. Single-strand sprockets are the most common, but you’ll also find many types that have multiple strands of chains. Multi-strand chains are generally larger and allow for greater torque to be transmitted from a common central shaft.
Another type is flat sprockets, which have no hub and drive through a series of holes. They are used for transmission of power or material in chain-driven systems, such as bicycles. They can also be used for overhead conveyors. In some cases, there is a special type that fits the shaft of an automobile, such as a transmission shaft.
There are many different types of sprockets, each with a unique function. Some are used for conveyor chains, while others are used for other applications. In most cases, sprockets are used in chain-driven machinery. They come in different sizes and pitches and are designed to work with particular types of chains.
When choosing a motor or transmission system, it is important to match sprockets and chains. A perfectly matched set of components will ensure that the motor and transmission work together. Generally, this alignment comes down to sprocket-to-sprocket matching. The process involves jacking up the motor and lining up the sprockets and chains. Then, the sprockets and chains are locked into place with cotter pins.
sprocket

Size of sprockets

To determine the correct chain length and sprocket diameter, the first step is to understand the difference between the diameters of the sprockets and cassettes. The smaller the diameters of sprockets, the lower the chain tension. The larger the sprocket, the longer the chain will need to be. This process requires the use of a derailleur that can roll a larger number of chains.
In addition to chain length, the spacing between sprockets is another important factor. If the sprockets are too far apart, the chain may slip through the sprocket. A smaller range of sprockets will prevent this and will increase the number of discrete gear ratios. In addition, if the chain skips over a sprocket, it will cause discomfort in shifting.
Choosing the correct size of sprockets is essential for cycling. Larger sprockets are usually necessary for road bikes. Likewise, a road bike will have larger gears than a gravel bike. Larger gears will help the cyclist accelerate more smoothly and ensure a smoother ride.
Using a chain calculator can help you determine the proper size of sprockets for your bike. You can also use a chain length calculator to determine the correct chain length. This calculator uses the distance between the sprockets to calculate chain length. However, it is important to note that it is not possible to calculate the length of a chain with a single sprocket.
The size of the sprocket must be in proportion to the length of the chain. It can be controlled by either adjusting the center of the sprocket or moving it to the proper position. The center of rotation of the sprocket is defined by the chosen geometry reference.
The report covers global and regional sales of sprockets. It also contains information on competitive dynamics and market concentration status. Moreover, the report includes detailed information about the manufacturers of sprockets. The study also includes regional and global market forecasts. It also provides a detailed breakdown of sales by type, application, and region.
When choosing the right size of sprockets, remember to take measurements and do some arithmetic. For example, a smaller countershaft sprocket will improve low-speed acceleration, while a larger rear sprocket will improve fuel mileage. In addition, it is recommended that you use the reverse sprocket size if you’re going to be riding on long highways.
sprocket

Maintenance of sprockets

Proper maintenance of sprockets and chains is crucial to the functioning of your bike. It is important to avoid overstretching them. If this happens, they will not fit properly and will require replacement. It is also important to prevent the kinks in your chain to reduce the amount of stress on your sprockets.
If you are unsure of the state of your sprockets and chains, you can replace them with a new chain and a new sprocket. If you notice that a chain is squeezing between the rear sprocket, it is time to replace the sprocket.
Proper maintenance of sprockets and chains involves cleaning and lubrication. Regular cleaning and lubrication can prevent damage and extend the life cycle of these parts. Proper lubrication will also ensure their smooth operation and minimize the noise. Regardless of whether your sprockets or chains are new or used, lubrication should be carried out at regular intervals to extend their useful life cycle.
Proper alignment of the sprockets and chains will ensure the most efficient performance and reliability. If you regularly change your chain and sprockets, you can prolong the life of these components and avoid costly repairs. Make sure you change the sprockets and chains only with professional mechanics. Always follow the instructions of the motorcycle manufacturer.
Proper maintenance of sprockets and chains is important to prevent premature sprocket replacement. Changing the sprocket too often can result in poor meshing, accelerating wear and tear of the new sprockets. When changing the sprocket, it is essential to turn the worn surface over before you install the new one.
It is important to follow the instructions and warning signs for proper maintenance of sprockets and chains. The safety of the workers and the environment should be prioritized. Follow the instructions of the manufacturer and avoid dangerous situations. It is essential not to anneal or electroplate the chain parts.
Proper lubrication is also vital. Use a non-petroleum based cleaner to clean the chain thoroughly and then apply lubricant. Avoid using engine oil as it is more viscous and cannot protect the chain against water.

China supplier Standard Rolling Gear Sea/Plywood Case Various Shaoxing Transmission Part Sprockets     with Hot selling		China supplier Standard Rolling Gear Sea/Plywood Case Various Shaoxing Transmission Part Sprockets     with Hot selling
editor by CX 2023-04-21

China Good quality ANSI Standard Sprockets Industrial Gear Teeth Rack Bevel Bicycle Stainless Transmission Drive Part Carbon Steel Plate Idler Wheel Roller Chain Sprocket with CE crank and sprocket

Product Description

 

Product Description

Heat treatment Harden teeth, tempering, queching
Surface treatment zinc plated, blacken, phopharization, carborized
Process Forging( casting)—lathe- teeth shaping—finishing—oil washing—Packing ,made by CNC machine
Inspection All items are checked and tested thoroughly during every working procedure and after the product is finally manufactured to ensure that the best quality product enter into the market.

Company Profile

In 2571, HangZhou CZPT Machinery Co.,ltd was established by Ms. Iris and her 2 partners(Mr. Tian and Mr. Yang) in HangZhou city(ZHangZhoug province, China), all 3 Founders are engineers who have more than averaged 30 years of experience. Then because the requirements of business expansion, in 2014, it moved to the current Xihu (West Lake) Dis. Industrial Zone (HangZhou city, ZHangZhoug province, China).

Through our CZPT brand ND, CZPT Machinery delivers agricultural solutions to agriculture machinery manufacturer and distributors CZPT through a full line of spiral bevel gearboxes, straight bevel gearboxes, spur gearboxes, drive shafts, sheet metal, hydraulic cylinder, motors, tyre, worm gearboxes, worm operators etc. Products can be customized as request.

We, CZPT machinery established a complete quality management system and sales service network to provide clients with high-quality products and satisfactory service. Our products are sold in 40 provinces and municipalities in China and 36 countries and regions in the world, our main market is the European market.

Our factory

Our sample room

Certifications

Why choose us?

1) Customization: With a strong R&D team, and we can develop products as required. It only takes up to 7 days for us to design a set of drawings. The production time for new products is usually 50 days or less.

2) Quality: We have our own complete inspection and testing equipment, which can ensure the quality of the products.

3) Capacity: Our annual production capacity is over 500,000 sets, also, we also accept small quantity orders, to meet the needs of different customer’s purchase quantities.

4) Service: We focus on offering high-quality products. Our products are in line with international standards and are mainly exported to Europe, Australia, and other countries and regions.

5) Shipment: We are close to HangZhou and ZheJiang ports, to provide the fastest shipping service.

Packaging & Shipping

FAQ

Q: Are you a trading company or manufacturer?
A: We’re factory and providing gearbox ODM & OEM services for the European market for more than 10 years

Q: Do you provide samples? is it free or extra?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.

Q: How long is your delivery time? What is your terms of payment?
A: Generally it is 40-45 days. The time may vary depending on the product and the level of customization.
For standard products, the payment is: 30% T/T in advance,balance before shipment.

Q: What is the exact MOQ or price for your product?
A: As an OEM company, we can provide and adapt our products to a wide range of needs.
Thus, MOQ and price may greatly vary with size, material and further specifications; For instance, costly products or standard products will usually have a lower MOQ. Please contact us with all relevant details to get the most accurate quotation.

If you have another question, please feel free to contact us.

Standard Or Nonstandard: Standard
Application: Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car
Hardness: Hardened Tooth Surface
Manufacturing Method: Rolling Gear
Toothed Portion Shape: Spur Gear
Material: Steel, Stainless Steel, Plastic,etc.
Customization:
Available

|

Customized Request